- Model# 600014U Ser# 12-10469 Gasket Kit 'NAPA Autoparts' PART NO.
- Replacement rubber/elastomer gaskets for underside of fuel cell cap # 910-76502. 1/8' thick Item Details Alcohol Fuel Compatible New for 2018! Value added kits are now available which includes both the cap and neck as kit # 916-02008 and a rollover flapper valve kit # 916-02007.
Parts Category List
Axle SealsBody partsBooks / LiteratureBrakesBrakes 1500Brake Kits & PackagesCablesCarburator R16Carburator U20Carburator Kits & PackagesCarburator Mikuni SolexClutchCoolingCylinder Head G15/R16Cylinder Head U20DashDifferentialElectricalElectrical FiringElectrical SwitchesElectrical OtherEmblemsEngine 1500/1600Engine 2000Engine Timing Components 2000Engine externalEngine Kits & PackagesEngine Room Decals & StickersEngine SealsExhaustExterior TrimFuel SystemsFront AxleGasketsGaskets CarburatorGaskets EngineGaskets Transmission DifferentialGlassHandles & LatchesHeaterInteriorInterior TrimZ Car InteriorFairlady 310 InteriorInterior Kits & PackagesLamps & LightsLocksKnobsMirrorsRear AxleRubber PartsRubber Kits & PackagesSoft TopsSteeringSteering Kits & PackagesSuspensionSuspension Kits & PackagesTransmission 4 SpeedTransmission 5 SpeedTransmission Kits & PackagesTransmission SealsUsed PartsWheelsWeatherstrippingWeatherstrip Kits & PackagesWiper & WasherMaterial & Carpet Swatches
Axle SealsBody partsBooks / LiteratureBrakesBrakes 1500Brake Kits & PackagesCablesCarburator R16Carburator U20Carburator Kits & PackagesCarburator Mikuni SolexClutchCoolingCylinder Head G15/R16Cylinder Head U20DashDifferentialElectricalElectrical FiringElectrical SwitchesElectrical OtherEmblemsEngine 1500/1600Engine 2000Engine Timing Components 2000Engine externalEngine Kits & PackagesEngine Room Decals & StickersEngine SealsExhaustExterior TrimFuel SystemsFront AxleGasketsGaskets CarburatorGaskets EngineGaskets Transmission DifferentialGlassHandles & LatchesHeaterInteriorInterior TrimZ Car InteriorFairlady 310 InteriorInterior Kits & PackagesLamps & LightsLocksKnobsMirrorsRear AxleRubber PartsRubber Kits & PackagesSoft TopsSteeringSteering Kits & PackagesSuspensionSuspension Kits & PackagesTransmission 4 SpeedTransmission 5 SpeedTransmission Kits & PackagesTransmission SealsUsed PartsWheelsWeatherstrippingWeatherstrip Kits & PackagesWiper & WasherMaterial & Carpet Swatches
After 43 years my gas cap started leaking when full, only ceasing to do so once 2 gallons had been used.
IMG_8451.JPG
Time for a new gas cap cork seal - p/n 16 11 1 230 603.
The pivot pin is serrated and only comes off to the left, using a pin punch:
IMG_8496.JPG
Vise grips depress the seal against the strong spring to expose the retaining rivet:
IMG_8484.JPG
A Dremel abrasive wheel is used to grind off the rivet head, taking care not to remove any of the post material:
IMG_8486.JPG
Dismantled - old seal - shot, spring and rubber spacer on shaft:
IMG_8487.JPG
The tricky bit. You need to drill a 0.17' (#17 drill size) hole dead center and perpendicular. I locked the cap in place in the wooden jaws of the vise, checking that the rim was equidistant either side from the surface using a dial caliper as a depth gauge, then clamped this simple right angle drilling jig to the bench after centering. I started with an oversize drill to establish a centered cone cut (a small drill bit is too prone to wandering), then switched to the #17. Sadly I sold my drill press years ago which would have made this easy:
IMG_8489.JPG
The drilled hole is tapped for an M6 x 1.0mm bolt, which is 0.23' in thread diameter (I'm mixing metric and English!):
IMG_8490.JPG
The tapped bore. I used WD40 as cutting lubricant:
IMG_8491.JPG
Ready for reassembly - rubber collar, spring, washer, lock washer and stainless steel M6 bolt, after blasting everything with compressed air. Blue Loctite is used on the threads:
IMG_8492.JPG
Job completed - note the vent hole to relieve tank gas pressure - orientation is irrelevant:
IMG_8495.JPG
The first seal lasted 43 years so I will be replacing this one when I am 110.
T.
Cork Gas Cap Gaskets
Glass bowl fuel filter cork gasket. $5.21: Fuel Systems Weatherstripping Gaskets: Partnumber: 2189 Datsun Roadster and Fairlady Early Gas Cap Gasket AFTER MARKET USA Correct 3.2 mm cork gasket. New stock soft and supple This part fits the 1 early gas cap. The photo of the gas caps shows the difference between the early and late gaskets. West Coast Metric: SEAL, CORK GASKET FOR 80MM GAS CAP, BUG 1956-60, GHIA 1956-60. I have a 1980 Puch Maxi w/original gas cap w/built in measuring cup. Watermelon man 1970. Auto clicker 2. The original CORK gasket had started falling apart. Fish hunter gambling game. This part is a perfect replacement for the CORK seal.
